REQUEST A QUOTE
Contact us by phone +39 0585 831034 or by e-mail firstname.lastname@example.org
Perfect for very large plants specialized in aggregates, earth and gravel treatment in quarries and mines. Magnum 2000×2000.
It is named after the Latin word for Magnificent, because it is our top-of-the-range machine, created for and completely dedicated to every kinds of applications in quarries and mines, that is to say for areas where men use the Earth for progress.
Pneumatic system to guarantee the detachment of the filtering cloth panels created with a series of high efficiency pneumatic cylinders. They lift a stainless steel bar by means of special pivots and then release the plate in order to give it a suitable ver- tical stress. Our shaker does not wear out and guarantees an efficient vertical shaking of the plate and the complete detachment of the mud cake. Protection and safety systems :
The Cake-Dryer is a 100% automatic system for the drying of the cakes of mud through the use of compressed air. The system is similar to that of the Core-Blow; the jet of compressed air is blown into the central hole of supply of the plates, thus allowing a drying of block of 20 plates, to have a final cake completely dry.REQUEST A QUOTE
A close circuit system for special mud with chemicals. It usually workstogether with the membrane plate system, allowing a clean water flowinside the plate chambers before cakes are discharged. This processrinses the cakes, to lower chemicals’ level under the “special mud” threshold.REQUEST A QUOTE
Core blow system is projected to clean the core at the end of the filtering process from the residual unsqueezed mud gathered in the diffusion conduit through the plates. The Filter press is equipped with an air conduit in the mobile plate to blow, at the end of the filtration process, the residual liquid mud back out of the plates. An appropriate valve system let the blown mud bypass the mud pump and be discharged in the mud tank again.REQUEST A QUOTE
During the filtering cycle a few drops of water can escape from the cloths, especially if these are new, so to avoid that fall of water on the mud cakes already discharged, Matec has created two particular types of drip. The “drip tray” system consists in a tray, composed by one or two tanks shifted, which occupies the part underneath the filter press during the filtering phase, then collecting the drops of water that escape; once the filtering phase has finished, the tanks are then moved by a motor to allow the discharge of the cakes. The “bomb doors” model has two doors that rotate to occupy the space below the filter. They are positioned with an inclination that allows them to collect the water that comes out, and then redirect it to lateral drips, where it will be sent back to the waste water tank.REQUEST A QUOTE
Matec filter presses have been created for the aggregates sector where HPT is essential for obtaining excellent results with difficult muds. While our competitors come from sectors such as olive oil, marble, and chemi- cals. HPT is more expensive, it needs MORE QUALITY and better components:
The filter press can be equipped with an automatic washing system forplates and cloths. The system is composed by one valve and one system of pipes on the mud head side of the filter press, and discharging val- ves on every single plate. The feeding pump sends clean water to wash the residual mud. The sytem washes the plates 20 by 20. The frequency of the wa- shing cycle is set through the operator panel.REQUEST A QUOTE
The RoboWash washing operation is a fully automated cloth washing system that can be put into operation at the touch of a button. The high pressure sprayer located at the end of a drop down curtain, slides between each plate and applies high- pressure wash water to the full area of the filter cloth, dislodging and cleaning any build up of dirt on the filter cloth.REQUEST A QUOTE
The membrane plates are special plates with one internal chamber and one membrane. The membrane allows a bettermechanical squeezing of drying mud cakes. Basically, the membrane is inflated with water and grows in volume pressing on the sludge whi- ch is pumped into the chamber. A non-fixed volume is the main difference with standard plates. The special plate, together with the drainage system, guarantees a dryer final product and a more efficient filtration cycle. Also the discharging of the cakes is bene- fited. The material for the membrane may vary using different techno-polymers to meet customers’ requirements and depen- ding on the material to be treated, usually it is a variety of polypropylene.REQUEST A QUOTE
This system consists of proximity sensors, upper and lower ones, to control the tilting of the last closing plate. In the software that manages the filter press you can set the delay time between the two sensors. If the second sensor activates within the set time after the first one, the machine can continue its cycle normally. Otherwise an alarm will go off.REQUEST A QUOTE
It is placed in the freshwater storage tank, turbidity meter consisting of a candle measuring machine (sensor) immersed in water, with dissolved particles. Based on the feedback that is obtained from the measurement system, it is possible to determine where to direct the flow of water. Through pre-set values, if it is detected a too high level of turbidity, the system switches two valves and diverts the flow of water from the fresh water tank to the waste water collection tank, to resubmit the water to the clarification phase.REQUEST A QUOTE
The TT2 System is patented by Matec to solve the problem of sludge discharging opening and closing dead time in filter presses. Thanks to this system that reduces also the length of the machine, the process of plate discharging has decreased from the usual 15/20 min to 3 min for 150 plates. This system guarantees also a 30% increase in productivity and a reduction in operating and maintenance electrical costs, in addition to an easier use of the machine. The TT2 works by opening the main cylinder just once, then it closes, in order to open the first 10 plates. The quick opening of the plates is used to open 10 plates at a time through the back and forth shifting. The two oleodynamic cylinders “TT2 Fast”, installed on lateral bars and provided with mechanical modules. The opening of 2 cylinders works at high speed through the oleodynamic power unit.REQUEST A QUOTE